208 lines
7.4 KiB
Markdown
208 lines
7.4 KiB
Markdown
# ambium
|
||
|
||
Analog white-noise generator. Single **+12 V** supply, breadboard-friendly.
|
||
Broadband hiss to a **4 Ω speaker** via a TIP120 driver.
|
||
|
||
Reference designators and model numbers are consistent across every diagram, the
|
||
BOM, and the connection list — the connection list is the authoritative netlist.
|
||
|
||
## Parts
|
||
|
||
- **U1** = LM358 (dual op-amp, DIP-8). U1B = amp. U1A unused (inputs tied to VREF).
|
||
- **Q1** = 2N3904 (NPN). Avalanche noise source.
|
||
- **Q3** = TIP120 (NPN Darlington, TO-220). Class-A speaker driver.
|
||
|
||
## Nets
|
||
|
||
`+12V` · `GND` · `VREF` (6 V mid-supply) · `NOISE` · `AMP` · `SPKR`
|
||
|
||
## Signal chain
|
||
|
||
```
|
||
[noise] [amplify] [driver]
|
||
Q1 2N3904 → U1B LM358 ×1000 → Q3 TIP120 → 4Ω speaker
|
||
NOISE AMP (class A)
|
||
```
|
||
|
||
Legend:
|
||
```
|
||
[Rxx val] resistor ──┤├── film / non-polar cap ● junction
|
||
──+┤├── polarised cap (+ = + terminal)
|
||
│\ × no-connect
|
||
────┤−\ op-amp: IN− top, IN+ bottom, OUT right. ► net continues
|
||
│ >── Powered from +12V / GND (LM358 pins 8 / 4).
|
||
────┤+ /
|
||
│/
|
||
E transistor: E / B / C labels outside the box.
|
||
│
|
||
┌──┴──┐
|
||
B ───┤ Qx │ NPN
|
||
└──┬──┘
|
||
│
|
||
C
|
||
```
|
||
|
||
---
|
||
|
||
## Power · VREF divider (R2, R3, Cref)
|
||
|
||
```
|
||
+12V
|
||
│
|
||
[R2 10k]
|
||
│
|
||
●───────────────┬────────► VREF (6 V)
|
||
│ + Cref 10µF
|
||
[R3 10k] ──┤├──
|
||
│ −
|
||
│ │
|
||
GND GND
|
||
```
|
||
R2/R3 = 20 kΩ across 12 V, midpoint = 6 V. VREF = AC ground (single supply).
|
||
|
||
---
|
||
|
||
## Stage 1 — White noise (R1, Q1, C1)
|
||
|
||
Reverse-biased B–E junction of Q1 into avalanche = broadband white noise. R1 limits
|
||
current; C1 couples it out.
|
||
|
||
```
|
||
+12V
|
||
│
|
||
[R1 100k]
|
||
│
|
||
●──+┤├──────────► NOISE
|
||
│ C1 10µF (+ → emitter side; − → NOISE)
|
||
E
|
||
┌──┴──┐
|
||
GND─B─┤ Q1 │ 2N3904
|
||
└──┬──┘
|
||
│
|
||
C × no connect
|
||
```
|
||
NOISE = the AC-coupled output after C1. The ● node is raw noise on a DC pedestal —
|
||
internal, don't label it.
|
||
|
||
> Avalanche varies part-to-part. If quiet, swap the 2N3904. Needs full +12 V.
|
||
|
||
---
|
||
|
||
## Stage 2 — Amplifier ×1000 (U1B, Rin1, Rf1)
|
||
|
||
Inverting amp, gain ≈ −Rf1/Rin1 = ×1000, centred on VREF. Clips into the rails at
|
||
this gain — that's the loud hiss fed to the driver. Too harsh? Drop Rf1 (e.g. 470k).
|
||
|
||
LM358 DIP-8, notch at top, pin 1 top-left. Amp = **unit B** (pins 5/6/7).
|
||
|
||
```
|
||
┌────∪────┐
|
||
┌───── OUT A 1┤● ├8 V+ ──── +12V
|
||
└───── IN− A 2┤ ├7 OUT B ──●──────────────► AMP
|
||
VREF ──── IN+ A 3┤ LM358 ├6 IN− B ──●
|
||
GND ──── V− 4┤ ├5 IN+ B ──── VREF
|
||
└─────────┘
|
||
|
||
feedback (pin 7 ↔ pin 6): pin 7 ●──[Rf1 1M]──● pin 6 Rf1 ∥ Cf1
|
||
pin 7 ●──[Cf1 22pF]─● pin 6 anti-osc, limits BW
|
||
|
||
input: NOISE ─[Rin1 1k]──● pin 6
|
||
```
|
||
Unit A unused → park as a follower so it can't oscillate: pin 3 → VREF, pin 2 → pin 1.
|
||
Power/decoupling (whole chip, once): pin 8 → +12V, pin 4 → GND. 47µF bulk + 0.1µF at
|
||
pin 8.
|
||
|
||
---
|
||
|
||
## Output driver — TIP120 class-A follower (Q3), 4Ω speaker
|
||
|
||
AMP is line level; the LM358 can't drive a speaker. Q3 emitter follower supplies the
|
||
current. Class A — needs a heatsink.
|
||
|
||
```
|
||
+12V +12V
|
||
│ │
|
||
[Rb1 10k] C (collector)
|
||
│ ┌──┴──┐
|
||
●───────●───────────────────B──┤ Q3 │ TIP120
|
||
│ │ └──┬──┘
|
||
[Rb2 10k] │ │
|
||
│ │ E
|
||
GND │ │
|
||
│ ●──+┤├──► SPKR ─ GND
|
||
AMP ─+┤├───┘ │ Cout2 470µF (+ → emitter)
|
||
Cc 10µF [Re 22Ω 3W] 4Ω
|
||
│
|
||
(base node ● = Rb1/Rb2/Cc) GND
|
||
```
|
||
The base node ● sits at ~6 V (Rb1/Rb2). Cc lands there and adds the AC — it never
|
||
connects to +12V.
|
||
- Rb1/Rb2 = 10k/10k → base ~6 V. Cc AC-couples AMP onto the base.
|
||
- Emitter ~4.5 V (base − ~1.5 V Darlington drop). Iq = 4.5V/Re ≈ 200 mA.
|
||
- Cout2 blocks DC; speaker sees AC only.
|
||
- **Heatsink Q3** (~1.5 W idle). Re ≥3 W.
|
||
- Cooler/quieter: Re = 47 Ω → Iq ~100 mA.
|
||
- Bias sag (hum/distortion): stiffen divider to 4.7k/4.7k.
|
||
|
||
TIP120 pinout (TO-220, face up, pins down): **1 Base · 2 Collector · 3 Emitter**.
|
||
|
||
---
|
||
|
||
## Bill of materials
|
||
|
||
| Ref | Value | Part | Function |
|
||
|-----|-------|------|----------|
|
||
| U1 | — | LM358 (DIP-8) | U1B amp (U1A unused) |
|
||
| Q1 | — | 2N3904 | avalanche noise source |
|
||
| Q3 | — | TIP120 | class-A speaker driver |
|
||
| R1 | 100k | resistor | avalanche current limit |
|
||
| R2, R3 | 10k | resistor | VREF divider |
|
||
| Rin1 | 1k | resistor | amp input |
|
||
| Rf1 | 1M | resistor | amp feedback (×1000) |
|
||
| Rb1, Rb2 | 10k | resistor | Q3 base bias (~6 V) |
|
||
| Re | 22Ω 3W | resistor | Q3 idle-current set |
|
||
| C1 | 10µF | electrolytic | noise coupling |
|
||
| Cref | 10µF | electrolytic | VREF bypass |
|
||
| Cf1 | 22–100pF | ceramic | amp feedback / anti-oscillation |
|
||
| Cc | 10µF | electrolytic | AMP → base coupling |
|
||
| Cout2 | 470µF ≥16V | electrolytic | speaker coupling (big, for lows) |
|
||
| — | 0.1µF | ceramic | LM358 decoupling |
|
||
| — | 47µF | electrolytic | +12V bulk |
|
||
|
||
Chip count: 1× LM358 + 1× 2N3904 + 1× TIP120. Q3 needs a heatsink.
|
||
|
||
---
|
||
|
||
## Connection list (authoritative netlist)
|
||
|
||
```
|
||
+12V : R1.1, R2.1, U1.8, Rb1.1, Q3.collector, 47µF+
|
||
GND : R3.2, Q1.base, Cref.−, U1.4, Rb2.2, Re.2, 47µF−, 0.1µF
|
||
VREF : R2.2, R3.1, Cref.+, U1B.IN+(5), U1A.IN+(3)
|
||
U1A.OUT(1) = U1A.IN−(2) (spare amp parked as follower)
|
||
(src) : R1.2, Q1.emitter, C1.+ (internal raw-noise node)
|
||
NOISE : C1.−, Rin1.1 (after C1)
|
||
AMP : U1B.OUT(7), Rf1, Cc.1 (Rin1.2, Rf1, U1B.IN−(6) = summing)
|
||
base : Cc.2, Rb1.2, Rb2.1, Q3.base (~6 V bias)
|
||
SPKR : Q3.emitter, Re.1, Cout2.+ ; Cout2.− → speaker → GND
|
||
Q1 : collector = no-connect
|
||
```
|
||
|
||
---
|
||
|
||
## Build & test order
|
||
|
||
1. **VREF** — confirm ~6.0 V.
|
||
2. **Noise (R1, Q1)** — scope Q1 node → hiss (~mV). None? swap 2N3904 or raise supply to 12–15 V.
|
||
3. **Amp (U1B)** — scope AMP → loud hiss (~volts).
|
||
4. **Driver (Q3)** — feed AMP through Cc. Speaker hisses. Q3 warm, not hot; too hot → raise Re.
|
||
|
||
## Tuning
|
||
|
||
| Want | Change |
|
||
|------|--------|
|
||
| Louder | ↑ Rf1 (watch clipping) |
|
||
| Less harsh | ↓ Rf1 |
|
||
| Cooler driver | ↑ Re |
|
||
| More headroom | ↓ Re (hotter — bigger heatsink) |
|